universal t board help

[magman687]

hey guy i got the t board in my angel and i need help setting it up well all i need is the settings the gun shoots ropes in full auto but in semi or reactive it shoots alot of blank shots .

some info all modes where with eyes on and yes there work right

dwell is 15 and i tried 13 and even as high as 30 and still shoots the same and i turned eye delay way dow and way up didnt help any.

like i said the odd part is that it shoots so great in full auto and 3 rnd burst pretty much any rappid fire mode.

now i will say in reactive and semi it shoots good at low bps but above like 9-10 it skips alot.

but i had it full auto 25bps just fine im so lost am i over looking somthing small here?

shibbs i hope u can help me or maybe the doc knows

anyway thanks for looking guys.

[Shibbykins]

universal tboard? am i missing something or have i just not had my coffee today

[magman687]

lmao whats up bro no u heard me right the board from sanareio dreams *SP

[Shibbykins]

link me

[magman687]

http://www.scenariodreams.com/productpages/universaltboard.htm

http://www.scenariodreams.com/manuals/universal_manual.htm

[Shibbykins]

oh THAT.... sell it n get a UN1

[Shibbykins]

what loader r u running

[magman687]

halo b and a eye force that i find to be better then the halo with z code

[Shibbykins]

what r all the settings your running on the tboard

and for §§§§s n giggles whats the pressure settings for your LPR and such

[magman687]

i have no clue what the lpr is set at i have only the half tool set u gave me lol.

ill try to remebder the settings i know dwell is at 14 eye delay is 5-7
thats about it other then rof and mode settings

[dr.strangelove]

Does the T-board have debounce settings? If so, have you tried adjusting them? Are you positive your eyes are functioning properly?

[magman687]

hi doc. yes i adjusted them and i epoxyed in the eyes lastnight just to make sure that they wernt jumping around when i was shooting it still does the same thing.

but i did some testing and i think it may not be my settings but a pressure problem i dont know what my lpr or hpr r set at but i just studied how it was shooting when i was dri fireing it and somtimes it seems at high rof it isnt recocking all the way so im guessing i need to turn up my lpr or hpr maybe both.

i dont know how to tell what my hpr is set at but i got some old kapp volly's im going to use 1 and make a lpr psi tool with it.

does that sound like it my be the prob that it may just not be getting the pressure it needs to run right?

[dr.strangelove]

A pressure problem usually will manifest itself in shootdown or incomplete cycling. I'm not perfectly clear on what you described before as "blank shots". If the gun sometimes doesn't completely cycle, or gets shootdown, or sputters and only farts a ball out the barrel, LPR is the likely culprit. If you just mean "blank shots" as in, you pull the trigger and the gun doesn't react to it, then that's more likely an electronics problem.

[magman687]

by blank shot i mean like dry fires and i made my lpr tool today it said my lpr is at 90 psi.
is 90 psi good?
and also i do get shootdown at about 18-20 bps not like rolling out of the barrel but like the ball with only go about 25-30 yards

[dr.strangelove]

90 psi is pretty much perfect for an LCD. If you're getting shootdown, make sure to clean and lube both your mini-reg and LPR.

As far as your other problem, if you just mean you're getting dryfires, then it seems the problem is not mechanical - the eyes are just letting the gun fire without a ball in place. Keep fiddling with your eye settings. I don't know a lot about the T-board's programming, but if it has eye sensitivity settings and an eye test, just get cozy with your gun, a ball and the board and get it all tweaked to where the eyes consistently pick up a ball. You might want to double check your eye alignment.

[magman687]

i might try another hpr on the angel and see how it does then.

[magman687]

ok so i put my nme reg on it and it didnt help it was at 90 psi from the lpr output with both regs and with my finger in the way of the bolt it went from 90 to 75-80 psi and with eyes off shooting it went down to 60 psi when shooting.

does that mean my lpr is the prob?

[magman687]

sorry i know its a noob thing lol i think it is the lpr on most guns that is what would cuase this prob but since i dont know much about angels i just want some1 to second that it is infact the lpr or most likely is.

[dr.strangelove]

I'm not sure I'm understanding you correctly - did you shoot the gun with your finger in the breech? Not a good idea with an HP Angel. Or even an LP one. But anyway, if your LPR pressure is dropping as you shoot, then yeah, your LPR isn't recharging fast enough. Try lubing both your regs like I said before.

[magman687]

i shoot it with paint but yes just to test it i used my figer with eyes off it still never has chopped the bolt it super easy on paint it just touches it then goes back to the resting position so with your finger in the breech it barly touches it the resets.

i thought that was a good thing i can stick a paintball half way in the breech and shoot 10 times and it wont break the ball.

[dr.strangelove]

It's great that it isn't chopping. It's just that at 90 psi you should have a real sore fingertip after doing that normally. It's probably not recharging very well and losing pressure. Definitely clean and lube both your regs.

[magman687]

ok will do ill get some paint soon and let u know how it works out.

[magman687]

well i got air/zballs and b4 i could even try them in the angel my noid is dead it still clicks but wont fire the gun i can hit the ornge button and it works.

and if i hold the ornge button on the back of the noid about half way down where u can barly hear the air hisssss it will fire when i pull the trigger.

i hate to ask it but i cant buy a noid does any1 have just the back peace of the noid the eletronic part that is all i need for a 2000 lcd i might be able to trade some small things like a cocker ram or cocker valve or somthing.

i took the hole noid apart and it is all clean FYI.

is there anything else i might try?

[dr.strangelove]

If the 'noid is functioning with the orange manual cycle button then the problem is most likely not with your 'noid. Check all your connections, make sure your battery is good, check all your connections again, make sure your switch is good, make sure your battery is good, and check all your connections again.

[magman687]

lol :D it seems the t board eats 9 volts.

it was new 2 days ago and i only clicked it about 4k times lol.

or is it just a high voltage noid?

but anyways it works now i only have my lp (450 psi) tank full so it has mass shootdown on it when i get my hp tank filled ill let u know how it goes. thanks for the help cya guys later.