05 speeding nowhere fast

[eardor]

hook up air turn it on the 2 orange lights light up and the red one then i put balls in it and it makes the orange ones go away and become green and red(showing eyes on and ball present)..and thats it wont fire wont do anything, its not leaking air and the air is flowing because i can hear it fill it up and push the bolt back, the person i bought it from isnt responding to my messages, i can run a angel with the screen but this is all new to me..any explanations?

[BoB]

What software version do you have?
What is your TR setting?
What is your dwell setting?
Does the board recognize a trigger pull?

[eardor]

i would say doesnt recognize trigger pull, because i cant turn the eyes on or off while the gun is on

[eardor]

yeah i cant even change settings with the grips off...set everything back to factory settings

[eardor]

is it possible to have the screw on the cover plate to tight? i loosened it up to check and air came out without me having a tank hooked up

[angel buyer]

It could be that your trigger simply isn't reaching the activation point of the board.

[eardor]

not sure whats going on now, turned it on and let it sit for a second and the lights switched from eyes on no balls to eyes on ball present, it has no air and no balls hooked to it.. board supposedly has the latest software update which i bought it like a week ago...still cant get a response from seller

[AHotdog]

If it lights up red and yellow at start that could mean a low battery...

[eardor]

they all light up when i first turn it on, then it shows the eye status...put new battery in, same thing

[AHotdog]

you said it was the stock board? are all the wires secure inside? and did the person you bought it from say there was any problems, sounds like you might need a new board.

[eardor]

yeah as far as i can see they are secure, just took out the eyes and tested them they seem fine, took off cover plate everything seems intack...i bought it from mike and ike on here and havent heard from him in a few days, but he never mentioned any issues... the board displays all the electronics

[AHotdog]

try adjusting the trigger, so that it goes further into the board, idk know if this is possible, but it could have gotten nocked around en route.

[eardor]

will try give me a minute....hey at least im learning my gun as i go

[eardor]

HOT DOG IS THE MAN!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!! you are my hero, except there was air trapped in the gun and i almost blew my foot off

[eardor]

ok another problem arises, there wa so much trapped air in it it shot 5 times and on the last shot blew a spring about an inch and a half long out

[AHotdog]

HOT DOG IS THE MAN!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!! you are my hero, except there was air trapped in the gun and i almost blew my foot off

lmao, smooth. congrats on your new Angel, but where did the spring pop out of? and do you think you can put it back in? pics might help

[eardor]

not sure i just saw it bounce, can you leave the vernier wheel screws and the screw that goes in the trigger off?looked at the manual and dont see a spring anywhere accesible

[AHotdog]

not sure what you mean, the locking screw? or the adjustment screws. does it still fire w/out the spring? not sure what it could be, let me check the manual before you gas it up again

[eardor]

yeah teh locking screw thru the trigger and the adjustment screws that hold the vernier wheels in place. the spring that flew out is at leats an inch long and thin

[Mavrick]

Are both the front caps over the tubes on the front of the gun?

[eardor]

ahhhh, i think i know what it is, its the srping that goes with the pull knob...do i really need that spring? itll make my gun lighter

[Mavrick]

So you have the back plate off then. That spring keeps the breach pin engaged so the breach stays locked.

[AHotdog]

I don't see the point in leaving the screw and wheels out, if you have the trigger out there should be no need to leave it out. also, is the little knob still on the back of the gun?

[eardor]

no, the back plate is on......but it use to have like some pressure to pull it out and now i can easly pull it out...so you suggets pputting the screws back in the wheels and trigger?

[AHotdog]

yeah, its probably a good idea to leave it in, so your breach doesn't open while you're shooting

[eardor]

how do you get that spring back in then

[AHotdog]

yeah, best to keep the gun sealed up good. but like pretty much everything in paintball, it's all preferance

[eardor]

can that pull knob spring be put back in without having to take anything apart because i just finally got everything back together

[AHotdog]

its just 2 bolts on the back plate to replace it if I remember correctly, but checking the manual is always a good idea

[eardor]

thanks for your help hot dog, if it wasnt 9:00 id go shoot it right now but ill have to wait until tomorrow..ill update you tomorrow after i fire it..thanks again...btw do you own a 05 speed?

[AHotdog]

I've done work on one and loved it, in fact I'm waiting to hear back from someone about one for sale. For the most part I enjoy teching guns almost, but not quite, as much as playing :P

[eardor]

yeah i cant wait to go and play with mine this weekend or at leats shoot it...if i have any more questions along the way can i just shoot you a pm?

[AHotdog]

sure, have fun, I'm going out for some outlaw ball this weekend at my friend's farm. Go shoot some faces.