Aznrevlazn
06-14-2007, 12:11 AM
Alot of people pm'ed me here and on PBNation on why I was using the A1 barrel kit on my Arsenal G7 Fly. They'd say how; and you'd prolly get breaks etc...
After one month owning A1 Small Bore kit I had yet to break a ball in the barrel... ...ever. But that space was annoying knowing that it was there. So I did what any tinkerer did, I made my own. I've had this spacer for a month and it has shown no negative results nor positive, it just fills the gap.
What you will need:
Your stock Infinity Barrel that you got with your G7Fly/06
Copper tube Cutter
Curved file
Your A1 Barrel
1. Make sure you measure out the difference, the difference that i got was a 9/32", but it may vary so make sure you measure twice cut once.
2. Mark your cutting area with a scratcher
3. Begin cutting the area tightening the cuter with every 10 full turns counter clockwise rotating the barrel.
4. After about 4-5 minutes you'll end with this product:
http://sars.darkstargamers.com/pics/WDP/G7%20Spacer/SANY0020.JPG
5. Now file the internal diameter of the spacer that you've just cut (be careful, the cut is fresh and may be razor sharp)
http://sars.darkstargamers.com/pics/WDP/G7%20Spacer/SANY0021.JPG
6. Be sure the spacer is level, you should always check
http://sars.darkstargamers.com/pics/WDP/G7%20Spacer/SANY0022.JPG
7. Insert your spacer
http://sars.darkstargamers.com/pics/WDP/G7%20Spacer/SANY0023.JPG
8. Enjoy knowing the fact that you have filled that space that your A1 barrel was unable to fill.
http://sars.darkstargamers.com/pics/WDP/Arsenal%20G7%20Fly/SANY0007.JPG
Above information and pictures are intellectual property of Regis Jung aka Sarsinajar/Aznrevlazn and Impact Paintball. Do not copy and past with you as the the intellectual owner, please give credit! Original Thread has been made on AOG and PBN do not duplicate and or replicate.
After one month owning A1 Small Bore kit I had yet to break a ball in the barrel... ...ever. But that space was annoying knowing that it was there. So I did what any tinkerer did, I made my own. I've had this spacer for a month and it has shown no negative results nor positive, it just fills the gap.
What you will need:
Your stock Infinity Barrel that you got with your G7Fly/06
Copper tube Cutter
Curved file
Your A1 Barrel
1. Make sure you measure out the difference, the difference that i got was a 9/32", but it may vary so make sure you measure twice cut once.
2. Mark your cutting area with a scratcher
3. Begin cutting the area tightening the cuter with every 10 full turns counter clockwise rotating the barrel.
4. After about 4-5 minutes you'll end with this product:
http://sars.darkstargamers.com/pics/WDP/G7%20Spacer/SANY0020.JPG
5. Now file the internal diameter of the spacer that you've just cut (be careful, the cut is fresh and may be razor sharp)
http://sars.darkstargamers.com/pics/WDP/G7%20Spacer/SANY0021.JPG
6. Be sure the spacer is level, you should always check
http://sars.darkstargamers.com/pics/WDP/G7%20Spacer/SANY0022.JPG
7. Insert your spacer
http://sars.darkstargamers.com/pics/WDP/G7%20Spacer/SANY0023.JPG
8. Enjoy knowing the fact that you have filled that space that your A1 barrel was unable to fill.
http://sars.darkstargamers.com/pics/WDP/Arsenal%20G7%20Fly/SANY0007.JPG
Above information and pictures are intellectual property of Regis Jung aka Sarsinajar/Aznrevlazn and Impact Paintball. Do not copy and past with you as the the intellectual owner, please give credit! Original Thread has been made on AOG and PBN do not duplicate and or replicate.