My First Angel what to know (Tadao Board)

[Shocker s/f]

I just bought this A4 off the nation and i would like to know what i should do to start using it

Stock Barrel
Gloss Red Angel A4 (2004)
MT Trigger
Custom Grips
red pull knob
A.F. FBS Tadao board
Angel Car charger of course
small, medium, and large volumizer
Can include 2 small cp volumizers

It has a Tadao Board as you can see so how does that effect the way i set the ball sensor and stuff. Im used to useing shockers and nerves and this is my first Wdp so any tips would help.

[PB 4 Him]

Step 1. Turn on.
Step 2. Pull trigger
Step 3. VIOLATE ANYONE ON THE OTHER END OF THE GUN!!!!!!!!!!!!!!!!:cry:

[Shocker s/f]

Violate lmfao umm ok

[thatguy!]

A4 or A4 Fly? Or a Flied A4?

If it's not a Fly or hasn't been flied, there's no antichop system to speak of with Tadao, and your ROF is capped at 20.

[Mavrick]

Tadao won't work without eyes FWIW..... so it has to be a A4 Fly or a Flied A4

[Shocker s/f]

It dont look like it has eyes :wowzer:
I guess i wont know till i actually get it.

[Shocker s/f]

This is the one i bought http://www.angel-owners.com/showthread.php?t=60859

Can i use a Hp tank on this or do i need to spend more money to get a Lp tank ??

[plum]

you can use an hp tank if you do that mod where you take out a shim or something, but if you dont and straight up use hp then youlll have trouble getting your gun to chrono under 300, itll be ~315

Nope, it doesnt have eyes, with eyes youll see two eye covers down the part where the detents are, like in this picture:
http://i83.photobucket.com/albums/j284/ostneb/100_0756.jpg

[Shocker s/f]

well sence i have the Gun and the board is capiable of using eyes, whats the milling and install cost ?? Any one know

[PB 4 Him]

[QUOTE=plum;542006]you can use an hp tank if you do that mod where you take out a shim or something, but if you dont and straight up use hp then youlll have trouble getting your gun to chrono under 300, itll be ~315

No, you can use the hp tank, I know this because I use one myself. I can chrono down to 50 fps, anthough I have a dye hyper2, not the stock mini reg.
My dad on the other hand has the mini reg and It works fine on his super low pressure phirana (about 275 psi)

[Trigga Nometry]

well sence i have the Gun and the board is capiable of using eyes, whats the milling and install cost ?? Any one knowCheck this out: http://www.angelforce.tv/conversion.html

You'd have to get the price for install but without the board since you already have it. Contact Bob or Ken and they will probably give you a quote for the eyue install.

[PB 4 Him]

About the milling I did my angel eyes 2day. it was very easy if you have a drill press, you can do it in about an hour. Just 4 holes and tap 2 of them.

[Shocker s/f]

About the milling I did my angel eyes 2day. it was very easy if you have a drill press, you can do it in about an hour. Just 4 holes and tap 2 of them.

lol yeah i could see it now, my Angel getting stuck on the bit and spinning around at 200000000000000 kabillion rpms just waiting for the cat to step in its rotating path lol ouch

[PB 4 Him]

lol yeah i could see it now, my Angel getting stuck on the bit and spinning around at 200000000000000 kabillion rpms just waiting for the cat to step in its rotating path lol ouch

do it on a drill press. then you can do it at 60 rpm at least i can.

[plum]

i think full eye service with a4 fly board is 299, and euro speed board is 250 or something, im guessing if you had your board they could do for ~200-230ish