PDA

View Full Version : G7 Fly Intellifeed prob need some help

LowLude00
07-12-2006, 03:39 PM
just got my intelli on my g7 fly and i can only get a few balls out before halo b/v35 starts flashin red/green. changed board to stock same thing happens. heard it could be the motor but when i dont have intelli pluged in it works fine:notsure: . anyone know what it could be? thanks:boink:
Pest2001
07-12-2006, 03:47 PM
i had this problem with my halo b w/ v35 board and it was the paint i was using, so try different paint and check your board setting.
LowLude00
07-12-2006, 04:27 PM
i changed the v35 to the stock halo board and same prob. but ill try diff paint. and what setting do u change for the intelli this is my first angel and i went all out so still learnin ha. thanks for the help
Pest2001
07-12-2006, 05:02 PM
you might want to contact KEN CRANE and see what he says
Trigga Nometry
07-12-2006, 05:04 PM
What intellifeed settings are you using? What settings on the board?
LowLude00
07-12-2006, 08:18 PM
what one is the intelli setting?
Trigga Nometry
07-12-2006, 09:05 PM
what one is the intelli setting?On the Tadao board, it is the LED that flashes RED and BLUE. A setting of one is off. Anything higher is the Intellifeed dwell setting.

In other words, you have to have the Intellifeed feature turned "ON" on whatever board you are using. Not sure if that is your problem or not.
LowLude00
07-12-2006, 11:12 PM
i have stock board
Trigga Nometry
07-12-2006, 11:15 PM
Did you install the Intellifeed yourself or did someone else install it? It sounds like you might have the new MT Intellifeed and has a input for the stock board or the Tadao.

Who installed the Intellifeed and did the drilling so that you could plug the Intellifeed wire into your Angel from your loader?
LowLude00
07-13-2006, 11:15 AM
BOB installed it from FIXMYANGEL for me and set it up. only thing i changed when i got it was trigger adjustment and the dwell.
Trigga Nometry
07-13-2006, 12:13 PM
Since Bob did the install, you might need to contact him for this one.
LowLude00
07-13-2006, 03:28 PM
i have and all he said is it could be the board or motor. i changed board same thing. i dont understand how it could be the motor that works fine. unless theres something diff with the intelli and the motor but i was thnkin of gettin new motor.
LowLude00
07-13-2006, 03:31 PM
i dont wanna send it back cuz i dont wanna pay the shipping and stuff tryin to get it workin with out doin that
Mavrick
07-13-2006, 07:26 PM
I saw this when I was testing and prototyping the new Intellifeed design. Put in a fresh set of batteries! All of them to! If you got one in there that is low it might give you the problem. The second thing I would recommend is to remove the Halo eyes and clean them good. When you put them back do not use the blue tape. Use good quality black tape. If light gets in there you can get a messed up signal to the board. Let us know after you do these two things how you make out!
LowLude00
07-14-2006, 02:59 PM
well i did what u said got new tape batteries and made sure eyes were clean. filled up the hopper turned on gun and BLASTED paint. filled it up again same thing no prob with intelli now i hope.ha but before i couldnt even get a hopper let alone 2 threw the gun at ease. well thanks for all the help everyone. peace