what is mdb

[i luv me angel]

i have asked a freaken million people what mdb is and they dont know or they dont answer, and what is yours set on:notsure: i have a g7 fly

[Trigga Nometry]

Mechnical de-Bounce setting.

I usually set it to OFF unless I have a very bad bounce problem.

This might help: http://www.angel-owners.com/showpost.php?p=431394&postcount=29

[KGBAgent185]

Mechanical Debounce. I have yet to recieve my Fly, and only know information that I've read and researched, I have read/researched a lot.

It's to prevent the gun from interpreting things that ARE NOT trigger pulls to BE trigger pulls. IE, The gun only fires when the trigger is pulled, and only fires once per trigger pull.

Debounce is a term used when talking about pulling the trigger rapidly and having a kind of ramping rate of fire where your marker shoots more paintballs than the trigger has been pulled. IE you pull the trigger quickly 5 times, the marker fires 7 times.

As for specific setting to put it at, again, I won't have my new marker until Thursday.

[i luv me angel]

is it the same as tr

[KGBAgent185]

Not sure what TR is... :( sorry

[WallyR]

Debounce often happen when you make does somewhat violent moves, like belly-slide and jumps.
A debounce occur when a bump to the marker makes the trigger move enough to hit the trigger-spot.
I think TR (Trigger Response) is deciding the trigger-spot, while MDB (Mechanical DeBounce) decides how far beyond the trigger-spot the trigger has to go before its actually counted as a triggering.

The MDB setting can usually be checked by holding the marker in one hand and hitting the gastank or marker in the end and see if it fires.
The hit should be just as hard as the bumps you get when you are landing in a belly-slide or from a jump.

The MDB is used to prevent the gun from firing in these situations, because thats usually when you do not want to fire it.
There can be teammates in the same bunker you slide into with a belly-slide and your marker would normally be pointing towards the bunker you are sliding into, so a debounce in this case could actually mean you would be taking your teammate out. :)

[Fly-n-High]

My Dumb Bitch!

Ahhh just kidding sweetie! I love ya!

[i luv me angel]

so trigga if you set it on 20 you will have the lowest chance of bouncing

[KGBAgent185]

so trigga if you set it on 20 you will have the lowest chance of bouncing

The text seems to point in the other direction, at 20 having the MOST filtering, therefore it's filtering as much noise out as possible, therefore you will always only get 1 shot per 1 pull.

The "Noise" is what is causing the bounce.

[i luv me angel]

oh thanks

[Shades]

so trigga if you set it on 20 you will have the lowest chance of bouncing

No not if your trigger is set up correct.

The lowest setting of MDB is 1 if you set it 3 or above your marker will add balls per trigger pull just like ramping.


This has nothing at all to do with hitting your marker etc it is about filtering out or adding impulse noise. Has the manual says not to be used to add trigger bounce. (This means make the marker add balls per trigger pull, it will if you set this higher than about 3)

[Eclipse363]

TR is the setting that ADDS shots when it is set to anything higher than 1. MdB is a tigger bounce filtering software, it makes the gun register a shot only once when the trigger has been pulled. It has to do with how a switch behaves in a circuit, but basicaly when a switch is throw it bounces ON OFF ON OFF ON OFF all in the timeframe of nano seconds. So MdB filters out the bounce and just registers the one intended activation. The recommended setting is TR 1, MdB 5. This will result in a legal one shot one pull gun, unless you have a problem 5 is plenty for MdB.

[Pelaez]

Can i use debounce in 1 mode, and how it is display it on the board?

[Eclipse363]

yes, its displayed as MdB #

[i luv me angel]

my g7 fly is on mode 1 tr 22 and mdb 1 and it still does not bounce

[Eclipse363]

its adding shots when you rapid fire if you are tr 22, you just cant tell.

[Trigga Nometry]

my g7 fly is on mode 1 tr 22 and mdb 1 and it still does not bounceReset the ROF to zero it out and try again. Then check what it reads as the maximum ROF the gun shot. My guess is that, yes, it is bouncing.

If you want it to bounce more, then you might have to adjuct your trigger to get it to bounce more.

Either that or just practice pulling the trigger....a lot...and you'll be able to pull it fast on your own lol.

[i luv me angel]

Reset the ROF to zero it out and try again. Then check what it reads as the maximum ROF the gun shot. My guess is that, yes, it is bouncing.

If you want it to bounce more, then you might have to adjuct your trigger to get it to bounce more.

Either that or just practice pulling the trigger....a lot...and you'll be able to pull it fast on your own lol.
did it and it said 14bps and if i have tr on 1 instead of 22 it is still the same?

[Brad7]

If you want more bounce adjust your TR and set it to 22. Your RoF should be in the 20's, or as fast as your loader feeds.

[tgallo]

and remember...you have to test WITH paint because without paint you have to turn the eyes off and it caps it at 15bps

[Trigga Nometry]

If you want more bounce adjust your TR and set it to 22. Your RoF should be in the 20's, or as fast as your loader feeds.Exactly, and YES make sure you use paint because it is capped at 15bps with the eyes off.