Help??????

[Paintball is Life]

I took the backplate off my gun you fix the switch and a screw fell of out its a little less than a inch long. ANd now my the thing that holds my bolt thing in won't work right. I think they are related but I couldn't get it to work
Robert
SOmeone Help IDK what to do

[angelguy3]

I think you need the screw.

[Paintball is Life]

WHat screw. ID have the Manual and can't dowlaod it I need help. I have everything that was in there nothing else was in there and it was working perectly before
Robert!!!!!!!!!!!!!!!

[El Pirata]

There's a link to the manual:
http://www.wdp.tv/manuals/

I think the thing you are missing is the spring for the breech rod. If you can't find one you can substitute that spring with one from a ballpoint pen, providing the diameter and length is similar.

[Paintball is Life]

I know its the back spring but it won't work right sitll
Robert

[firemedic30]

How do you have the spring facing?? You do mean the breech rod spring???

[Paintball is Life]

ya I think its the breech rod spring and there is a litt nob on the breech and it is infront of that.Get what I mean
Robert

[firemedic30]

If you have everything, then put one end of the spring on the nub, bend the other part of the spring back toward the back plate and place the rod into the channel. Then put the backplate back on.

[Paintball is Life]

OK the breech rod spring wilkl go in but its still not working right. But now I got more problems the on/off switch on the gun if now messed up and won't work any suggestions. I will post pics if anyone needs them. Tell me if you don't understand the problem
Robert

[Paintball is Life]

I am feakin doomed the wires that where soddered to the on/off swithc on the back plate came off. there both not soddered anymore. I can probly get one of the wires back on but the other one is to short. The stupid Breach rod still won't go back in. IDK whats wrong with it cause I have the manual its looks fine. and I can't get the front macroline fitting off. ANy Suggestions.
I am dooomed
Robert

[Roco]

Calm down. Unless the wires have been shortened, you should have enough wire. Remove the display side of your grip to see if the balance of the wire is tucked in there. If so, feed it through the hole at the top of the trigger frame to give you some slack.

Regarding the spring, you need to put the breach rod in as far is it will go first. After the rod is in, add the spring. It’s difficult with the spring sticking out the back, but put the back plate on. It helps to take the breach knob of the back of the rod.

The spring rests between “the knob” (not the breach knob you pull on to open the breach) on the rod and the back plate. The pressure pushes the rod toward the front of the gun. Rod then spring then back plate.

Good luck

[Paintball is Life]

Sorry if I sound crazy but I have tryouts tommorrow and I have never even got to shoot this gun cause it has had problem after problem. Any advice on loosening the macroline front fitting cause it won't come out and I need it out cause it is leaking.
Robert

[Roco]

Make sure you have all the gas out of the gun. Push the outside pressure ring on the fitting in while pulling the line out. It looks like you have a good bend in the hose, so take off the dropforward first.

While you have the line off, put a 2-3 drops of approved paintball oil in the new line before replacing it. This will work its way through the gun when you fire it. Pull the bolt out and clean any excess oil off after you shoot it 10-20 cycles.

[Paintball is Life]

I know how to oil it and I have oiled it I need the macroline fitting off the one going to the mini reg I think. But it is way to tight on there can't even budge it
Robert

[Roco]

I thought you were referring to removing the line. If you are talking about the fitting, most of the straight pressure fittings are removed using an allen wrench inserted up the middle where the micro line goes. It’s been a while since I’ve looked at the one on my gun so I’m not sure. If it’s not and the fitting is the problem, use vice grips to remove the fitting. If it’s bad, you’re gonna replace it anyway.

[Paintball is Life]

still not coming off IDK y its like its bolted in there it won't move at all
Robert

[Roco]

You do know it's threaded and won't just pull out right? You should be able to use an allen wrench and turn it clockwise.

[Paintball is Life]

I know its thread ( any dumass would know that) It won't move at all not even buge. Um and bout soddering the wires back on any tips or should I not even try it
:stooges:
RObert

[firemedic30]

Soldering is an art all of itself. If you don't feel comfortable, then get it to someone else.
As far as the breech and spring, just put everything back in place, and work the rod a couple of times. When I replace mine, it holds up just a bit and I just work it in and out and then no prob!

[Paintball is Life]

Ok guess what guys
Got 2 problems fixed figured out how to make the wires work for a day and then I will take it to the shop in brandon (30 min away) to fix it normally. Then I figured out how to do the breech rod.
The macro line fitting still won't come off but w/e I will get my shop off
RObert

[firemedic30]

Good luck with the fixing and the try outs!

Give'em hell!