who knows all of the good settings for the advanced mode for the fly

[AduBs]

hey i got a fly and owned everyone the first time i went out so i wanted to try the next modes so i did then when i went back to mode 1 everything was reset and everything that the guy had set for it from where i baught it was gone soo.... i read the manual and i still have no clue what are some good settings for the advanced mode so if you have any good settingsby the way i have a halo b hopper to set the dwell,mrof,hopper T1.00?, hopper: A 1?, 75'F?,on "V",trip on,and rof????/ please help me!!

[Sparco]

Dwell - somewhere between 9ms-12ms
MROF - somewhere between 16-18bps w/HALO
Hopper T & A - not needed
Temp - nothing you can do
Vibes - on if you use the timer
Trip - reset it whenever you want to keep track of cycles produced
ROF - displays greatest achieve ROF between two trigger pulls

[AduBs]

thanks but what should i set them to..... i know what they are becasue i read the manual....2 times.... :drink: but what do you pball pros think i should set the settings to i have only gone threw one cass of paint.... thanks a lot!!if you have given me info....

[ToxicPaintballz]

You cant set trip vibes ROF and temp man...seriously read your manual this should be an easy solution.

[mpire123]

http://www.angel-owners.com/forumdisplay.php?f=107

[Sparco]

If you read my post you'd see that I recommended some settings.

[BuNkErEd]

You cant set trip vibes ROF and temp man...seriously read your manual this should be an easy solution.
^lmao^
adubs, the manual is your friend. read it dude. :nerd:

as for settings, let your gun break in and then you can start changing your dwell and lpr. until then, play with it like it is.

[AduBs]

allright i read it i know the good settings guys thanks for telling me and i knew that you could not set the rof,temp,tip, thanks what hopper setting's do you guys like A1,A2,A3,A4, and the seconds i read on my halo can't find the feed thing i have the mrof at 22 cause the halo said 20+ bps....so yeah with that said thanks again.....

[Sparco]

allright i read it i know the good settings guys thanks for telling me and i knew that you could not set the rof,temp,tip, thanks what hopper setting's do you guys like A1,A2,A3,A4, and the seconds i read on my halo can't find the feed thing i have the mrof at 22 cause the halo said 20+ bps....so yeah with that said thanks again.....

So let's try this again, seeing you've yet to "read" my initial post. Upon reading the manual you'll find that the T & A settings are for use with the intellifeed system. Considering that the intellifeed setup is not standard and would require a bit of leg work on the user's end I doubt you have it setup. This is further developed by the fact that you have a HALO and thus it's unlikely you've rigged your HALO for intellifeed (which is possible and not recommended).

Thus both of these settings are useless and should be ignored/disregarded. Your MROF is the limiter on the marker when the eyes are off, there is no setting when the eyes are on... it will feed as fast your loader will go (alright I lied the electronics are limited to 31bps). But once again... no loader feeds 31bps, including the V.35 HALO board.

Set your MROF to a comfortably low number so that should you use the marker without the eyes enabled the marker will not outshoot the loader. On a HALO I set my MROF to 17bps (15bps on z-board evoII).

Your hopper setting should be SFAST.

... Here's hoping my third attempt is absorbed. :hi:

[AduBs]

thanks but what about the hahah i'm joking thanks a lot for the input and the time spent helping me out i am sure i have got it now!! peace out and thanks trust me i'll be back with more stupid noob angel questions watch out

[Clowndog]

Take a look at the top of this page where it says "Ken 's Recommended set up for the FLY" Click there,,,, input ,,, smile!