help i think i ruined my A4

[NyCzToM22]

i don't know why when i gas it up and then degas it the gauge stays at "2" and it doesn't fire when i gas it up either.. its on semi 2 with sensi on.. also.. my gun was functioning properly this afternoon.. i am not sure if i have messed up my gun.. wheni turn the power on.. it goes into safe mode.. and flashes the number "48214" and then "Safe Mode" i try to imput that number in my screen and then enter it but nothing happens.. also i can't get into my menu's anyone know how?

[vap0r]

I bet 48214 is your board ID #.

What happens when you plug in a charger?

:notsure:

[cveale]

Make sure your trigger is not overadjusted to where its basically always in the fire position. Also if you couldn't fire then how were you degassing the Angel. The gun keeps a gas charge internally for a long time until you release it by firing the gun. The tank doesn't even need to be attached.

[Foosheezee]

Make sure you put your gun into "live" and have your trigger adjusted properly and not so short, as it seems like it is set improperly and is set to short. loosen up the wheels and make the trigger pull stupid long, then see what happens

[NyCzToM22]

ok is there a way to fix it? cause i have adjusted the wheels above the trigger.. and it still doesn't work.. i have the tank in the bottomline aired up.. still doesn't fire.. also when i turn on my a4.. it goes into safe mode and also flashed a number "48214" and the says "semi-2".. also i cannnot get into my menu's for some reason

[Jetwing@Impactpaintball]

ok try this, with the gun degassed, turn gun on, switch to live, and pull the trigger, if u dont hear a small click, then try adjusting the toe of the trigger, try one extreme, then the next (really far in and really far out) and if u still do not hear a click then there may be something wrong with the board or leaf spring... but if u dont hear any click no matter what, then thats the problem

[NyCzToM22]

what kind of click.. as in a click like a autococker trigger? cause when i p ull it i hear something.. but im not sure if thats the click im looking for..

[Jetwing@Impactpaintball]

the small click should like its being made by something electrical, (not the humming of the display light)

[52brandon]

definitely sounds like the trigger is stuck on fire, I would take the grip off over the board and make sure your leaf spring isnt stuck in. Also if you disassembled your gun and took the trigger out you may have put it back together wrong (I did that, but it is easy to correct)

[vap0r]

They are onto something! The trigger adjustment causing a problem is a good point!

Try this:

Take the board out of the grip frame, but leave the battery plugged into it. Make sure the leaf sping isn't malfunctioning. Turn the gun on.

If it boots up OK, then the trigger toe screw is probably adjusted too closely to a firing position. Increase pre-travel in the trigger stroke (front vernier wheel) and back out the toe screw.

If it doesn't boot up, well, then you have a whole nother issue.

[Sparco]

So one minute the gun is working 100% flawlessly and the next it's not and you didn't touch a thing? Are you not telling us everything? Perhaps the TOE became loose and moved in on you, that's not uncommon. Have you unplugged any wires, taken anything apart?

[NyCzToM22]

k fixed it guys! thanks a bunch.. and yea i forgot my brother used a allan key to adjust the screw on the trigger.. he might have made it to close to the firing.. but its all good now.. all left is i don't know how to get into the menus' im following the manual.. but not working.. also when im in safety.. theres a flashing with 5 digit number and semi 2.. when i press the green button.. it brings me into a 5 digit imput screen.. what do i imput int here?

[52brandon]

k fixed it guys! thanks a bunch.. and yea i forgot my brother used a allan key to adjust the screw on the trigger.. he might have made it to close to the firing.. but its all good now.. all left is i don't know how to get into the menus' im following the manual.. but not working.. also when im in safety.. theres a flashing with 5 digit number and semi 2.. when i press the green button.. it brings me into a 5 digit imput screen.. what do i imput int here?
yor trigger is still stuck in fire. The PIN that you can enter when you press the green button is to lock your gun and you have to hold the trigger and press the green button. The flashing 5 digit number is your ID number for your gun that alternates with your mode when you pull the trigger, try backing out your TOE more (the allen screw in your trigger) and make sure the trigger is adjusted all the way forward.

[Emmit]

your TOE screw (the screw in the trigger itself) is too far in, you've already said that...you need to adjust that out so that you can get off the firing point.

[Jouster]

your TOE screw (the screw in the trigger itself) is too far in, you've already said that...you need to adjust that out so that you can get off the firing point.
Yep. Emmit is right, as usual. ;)

To adjust it such that you can tell when you've adjusted it enough, turn your gun on and adjust it that way. When your LCD backlight goes off, it's adjusted into a non-firing position.

Jouster

[y0umissed]

Rtfm